radio control vehicles

The Extra 330 ARC is a great aerobatic airplane. The Extra 330 is an airplane that can do all the smooth aerobatics as well as all the wild 3D maneuvers. The kit includes a light-ply fuselage and cowling done in red, white, yellow, and blue. The wings are sheeted foam and covered with matching covering. All control surfaces have beveled leading edges and the control horn mounts are preinstalled. The leading edge of the wing is pre-shaped. The kit includes full color decals.

WHOLESALES!!! 6-pcs YELLOW BEE 2-channel R/C Remote Control Glider. Ready to Fly!!! "BEST SELLING RC PLANES" NEW! Ready to fly out of its box! complete system with radio, rechargeable battery and AC charger! SD3382 Yellow Bee Twin Engine Complete RC Airplane ....... **A Great First Plane for Beginners!** I personally bought and flew this plane because I was completely new to flying and did not want to Smash and Trash a $400.00 gas plane, thanks to this Park flyer, I'm ready to move to the next level. best of all no permit was required to fly this. I opted to purchase the longer lasting NiMH batteries (2) that can yield up to 40 minutes flight time between the two. A ready-to-fly R/C plane that's easy-to-operate, sturdy enough to "crash without being trashed". The R/C Ready To Fly (RTF) parkflyer has glider-like stability suitable for flight in small nearby areas like parks and ball fields. Recommended for Ages 12+. Ready-To-Fly right out of the box. Just add batteries to the transmitter, charge the flight batteries using the included charger, bolt the tail wing to the boom, connect the flap push rods and you're ready to fly! * **The Radio Transmitter*** The transmitter has simple 2-channel proportional joystick controls with trims. The left stick controls the throttle and the right stick controls the tail flaps for turning. It's kind of like driving a car except the faster you go, the higher you climb! The radio transmitter (shown above) also features trim controls for precise adjustments of throttle and flaps. The control range is 1500' to give you plenty of margin Ready-To-Fly right out of the box. Remarkable crash-tolerant construction The ability to "crash without being trashed" makes the park flyer a true "survivor" The Planes single-piece poly molded fuselage and fiberglass tail boom is exceptionally tough. Forget about those hard crashes that usually destroy front-end motors and propellers, because the YellowBee's motor and pusher propeller are rear-mounted. Tough, enamel-coated foam wings attach with rubber bands that pop off in a crash to prevent extensive wing damage. If you're a beginner you will be especially glad to know that I include several spare parts to help you through the ordinary mishaps which are all part of the learning process. You get the radio transmitter too! All you need to provide is 8 AA batteries for the transmitter. The parkflyer comes complete with RTF airplane with motor, receiver, throttle speed controller and servo installed. Two flight battery packs a

Designed in the late 1960s as a high performance fighter with a fly-by-wire control system, and with the ability to carry up to 10 AAMs, the highly maneuverable Su-27 was one of the most opposing fighters ever built at the time. The first 'Flanker-A' prototypes flew on May 20, 1977 and entered service as the 'Flanker-B' in 1984. The 'Flanker' has seen a number of aerodynamic changes since, and exists in a variety of forms today. The Su-27IB, or Su-34 designation, is a long range attack variant with side-by-side seating for two. The Su-27UB 'Flanker-C', or Su-30 designation, is a tandem two-seat long range interceptor and trainer. A navalized version called the Su-27K 'Flanker-D', designated Su-33, was designed in 1992 for deployment on Russian aircraft carriers. It has folded wings, retractable flight refueling probe, arrester hook, strengthened landing gear, and moving canard fore planes. Next generation 'Flanker' derivatives include the Su-35 and the thrust-vector controlled Su-37, both vastly more enhanced then the Su-27, with canard fore planes and the ability to carry up to 11 and 14 external stores, respectively. Su-27 Flanker is designed for the hobby enthusiast. Based on its full-scale counterpart, this Russian jet flight model has a high roll rate and even can do the famous "cobra maneuver" flight. Even a beginner can easily setup and stably fly this model. It is also made as a highly maneuverable model for intermediate to expert pilot. This model includes a radio transmitter, a speed controller, two electric brushless ducted fans, and 5 electric servos. You will definitely enjoy flying this model. Feature: 4 Channel Full Function Radio Controlled (Aileron,Elevator,Rudder,Throttle) 4 Channel Digital Proportional FM PPM High Quality and Performance Futaba Compatible Radio System Full aerobatic characteristics; inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible One of the best ducted fan jet in the market! State of the art components such as Twin Brushless Ducted Fans, 2x 18amp Brushless Speed Control, and 2200mah 11.1 Volt Li-Po Battery Pack Famous "Cobra Maneuver" available Turning front-wheel Rudder helps steer plane on ground on its scale landing gear for easy take off Ready to Fly in Just Minutes! Super tough, lightweight airframe! Perfect appearance and emulation (Scale appearance, great attention has been given to details) Shock Resistant Reinforced Fuselage and Strong Wings Can Take Off From Ground or Hand Launched Ground Take-Off can be performed easily Excellent Flight Performance Super easy and super stable electric powered scale R/C park flyer for beginner or middle-level users Stable inverted flight

The Extra 330L features a painted fiberglass fuselage. The wing panels, tail plane, and rudder are all made of high quality balsa wood and painted at the factory. This kit also features carbon fiber landing gear, spats and wing joiner. Also included in the Extra 330L is a pre painted canopy. The decals on the kit are already applied under the clear coating. This is a must have for ARF enthusiasts! Wing Span: 80" Weight: 15.64lb Length: 70.5" Engine Required: 2c 40 ~ 50cc Gas Radio 4 Channel 6 Servos ARF KIT ONLY. ENGINE/RADIO EQUIPMENTS SOLD SEPERATELY. ****************NOTE*************** Engine, servos, transmitter, and other electronic items are sold separately! This is an airplane kit only, no electronics! Assembly required. Due to the United States Post Office's International shipping size limit, we can not ship this item outside of the United States, except Canada.

2C 108~160 4C 120~140 ENGINE POWERED AEROBATIC AIRCRAFTThe new CMPro Giles-202 (1800mm) Version IIfeaturesEnlarged aileron and rudder surfaces for superb 3D performance and enhance responsive control of the plane.Fuselage, wings and control surfaces from quality balsa wood, ready covered in a unique design which is fresh, bright and surely draws attention no matter on the ground or in the air! Wingspan1800mmLength1820mmWeight5.1~5.2 kg Wing Loading82~84 dm/2 AirfoilNaca 0013 Wing Area62 dm/2 Radio Control 4 Ch 6 Servospurchase separately2 Strok Engine 108~160purchase separately4 Strok Engine 120~140purchase separatelyThe fiberglass cowl is painted with eye-catching colors to go with the entire unique deisgn.Removable top hatch for easy access and making assembly a joyful thing to do!All wooden components are laser-cut making production very accurate. Wheel pants are made from High Impact Polystyrene and protected by a clear coating.

The well-known Piper J-3 Cub 120 Engine powered scale aircraft is one of the most recognized designs in aviation. The CMPro model features all balsa construction except for the fiberglass cowl. This results in a light but strong model. Wingspan 2310mm Length 1500mm Weight 5.3~5.4 kg Wing Loading 69~71 dm/2 Airfoil Naca 4412 Wing Area 76 dm/2 Radio Control 4 Ch 5 Servos purchase separately 2 Strok Engine 90~108 purchase separately 4 Strok Engine 110~120 purchase separately The undercarriage design works really well as an anti-vibration system and greatly lowers the tendency to bounce during landing. Tailplane and rudder are tied with wires to make the system strong. Rims and tyres supplied with kit are custom-made for the CMPro Piper J-3 Cub. Our J-3 Cub is also designed to give super performance with 20cc gas engines. Easy access to put servos and other detailing. (Model pilot shown in photo should be purchased separately). Wing panels are joined together with the alloy tube supplied. Doors at the fuselage can be opened from both sides. The undercarriage design is imitated from the real J-3 Cub which acts as an anti-vibration system.

AT-6 Texan 160 - 82" ARF Nitro Gas Radio Remote Controlled Warbird Airplane The AT-6Texan is available in two stunning color schemes, pick the one that suits you best. Decals are already applied on the fusealge under clear coating for more durable use. This contains a fiberglass fuselage. Wing panel, elevator & tailplane are painted over high-quality balsa wood. The wing section is also fiberlgass moulded *RETRACT NOTE* The retract bays are built into the wing from the factory, so the retracts will drop right in. Specs: Wingspan 82" Fuselage Length 55" Recommended Engine Size 2c/160 Flying Weight 11.9 lbs - 12.3 lbs Wing Area 1,007 sq in Radio 4~~5 Ch 5~~6 Servos Airfoil NACA 2415 Features The AT-6 Texan is available in two stunning color schemes. Pick the one that suits you best! Decals are already applied on the fuselage under clear-coating for more durable use and shortens building time. The fuselage is fiberglass-moulded to maximize scale look. Wing panel, elevator and tailplane are painted over high-quality balsa wood. Accompanied by a painted canopy. To achieve a more scale appearance, the wing center section is also fiberglass-moulded. Design also allows optional retract fittings for easy assembly! ****************NOTE*************** Engine, servos, transmitter, and other electronic items are sold separately! This is an airplane kit only, no electronics! Assembly required. Due to the United States Post Office's International shipping size limit, we can not ship this item outside of the United States, except Canada.

SILVER North American AT-6 Texan 160 - 82" Nitro Gas Radio Remote Controlled ARF RC Airplane The AT-6Texan ARF Nitro Gas Plane includes decals that are already applied on the fusealge under clear coating for more durable use. This contains a fiberglass fuselage. Wing panel, elevator & tailplane are painted over high-quality balsa wood. The wing section is also fiberlgass moulded The North American Texan trainer is one of the most important aircraft of all time and is universally recognized. First built as the NA-16 in 1935, the Texan was in continual production for nearly 10 years and in active use for more than five decades. Primarily used as a trainer, the Texan remains a favorite among warbird collectors around the world. Wing Span: 82" Weight:12.33 lb Length: 55" Wing Area: 1007.5sq.in Wing Loading: 28.29oz./sq.ft. Engine Required: 2c 160 Radio: 4-5 Channel 5-6 Servos The retract bays are built into the wing from the factory, so the retracts will drop right in. Engine/Radio Equipments Sold Separately. Engine/Radio NOT included

de Havilland D.H Tiger Moth - 120 Giant Scale Radio Remote Control RC Bi-Plane ARF RC Bi-Plane "A charming touring plane that's almost ready to fly." Derived from the highly successful D.H. 60 Moth series of civilian aircraft that included the famous Gypsy Moth, the de Havilland D.H. 82A Tiger Moth is the quintessential British biplane trainer. The Tiger Moth has long been popular with modelers, and now with our low low price, you can, too, be own a part of this fascinating history. Our Tiger Moth 120 is a Almost-Ready-to-Fly model, built with all balsa and plywood. All parts are precovered with our quality film coating material. IMAA-legal dimensions contribute to its realistic flight characteristics and enhance the plane's incredible attention to detail. Whether you're a serious scale aircraft builder or an aspiring r/c sport flier-or both-you will be thrilled to own and pilot one of the world's most beautiful plane! Top quality balsa and plywood construction All wood constructions with fiberglass parts Trimmed and painted cowling by fuel proof paint Hand iron-on color film covering Comes with all hardware and accessories Wing span: 76in / 1930mm Wing area: 1830sq in / 118 sq dm Flying weight: 9.0lb / 4086g uselage length: 65.5 in / 1664 mm Engine Required: 4c 1.40cu in Radio Required: 4 channels,5 servos High-quality hardware is included for convenience. Best suited for the power and realistic sound of a 4-stroke engine, but will also fly well on a 2 cc engine within the recommended range. Dual aileron servos simplify assembly, and deliver more precision and authority to flying maneuvers. Ready for flight in as little as 20-25 hours. Most of the interlocking, all-wood parts have already been assembled into easy-to-assemble sections FLYING Takeoffs for the Tiger Moth 120 are very easy, even in slight crosswinds, and require very little rudder correction. Scale takeoffs are best achieved by slowly advancing the throttle and holding a bit of up-elevator as the model starts to roll. Even with only a lO mph headwind, the model will lift off within a few feet when you apply full power. Turns require a bit of coordinated rudder, especially during the climb-out. The model is capable of amazingly slow flight. Though not dramatic, deployment of the leading-edge slats enhances slowspeed control. The Tiger Moth could never be mistaken for a jungmeister, but it is nevertheless quite capable of many aerobatic maneuvers. Really nice loops, stall turns and wingovers are all easily within its capability, though its roll performance leaves something to be desired. Even with differential

The 50CC Yak ARF from NitroModels is a high performance aerobatic airplane, capable of both precision and 3-D maneuvers. The aircraft builds easily, quickly and precisely due to our state of the art CAD design with Laser cutting technology, and outstanding craftsmanship. The 50CC Yak ARF is designed for gas engines in the 50cc category. It is built with the highest quality balsa/plywood and is pre-covered. Fuselage length: 2060mm / 81 in Flying weight: 8000g Wing Span: 2160mm / 85in Engine : Gas Engine: 45cc - 50cc Engine Required: Gas Engine: 45cc - 50cc

Habicht ARF Glider Spray painted fiberglass fuselage. Ready covered built-up wings and tails. Available in two color schemes, red & whie or blue & white. Specifcations Wingspan.....................2600mm Weight.........................2900~3100g Lenght.........................1245mm Wing Area....................55 dm2 Wing Loading...............53~56g/dm2 Airfoil..........................Clark Y 61 Modify Radio..........................3~4 Channel 4~6 Servos

2.4Ghz F/A-18C Blue Angel Brushless Radio Controlled Jet 2.4Ghz F/A-18C, family member of ducted airplane "BLUE ANGEL" with scale appearance, can fly perfectly in low altitude at low speed! One of the fastest radio controlled airplane in the world. Features: ★Scale appearance and vivid flight gesture. ★Front landing gear could be turn around, resulting to easy swerve on the ground. Easy takeoff! ★Thanks to well-designed high-efficiency ducted fan and high KV brushless motor, it gives strong power. ★Power is very satisfied to do all aerobatic flight. ★With perfect capacity of low speed flight in low altitude, it can land airily. Specification: Wingspan: 686mm (27 in) Length: 1032mm/40.6in Height: 257mm/10.1in Flying Weight: 640g/22.6 oz Drive System: 4300KV Inrunner Brushless Motor Servo: 3X 9g high speed micro servos Speed Controller: 30 Amp Brushless Speed Control Battery: 11.1V 1600mah 3S 15C Li-Polymer Control system: 4 CH 2.4Ghz Transmitter Radio Control Range: 3000 feet (1000m) Package Include: Airplane (95% assembled) 4 Channel 2.4Ghz Radio Transmitter Wall Battery Balance Charger High Quality Rechargeable 11.1V 1600mah 3S 15C Li-Polymer Battery Simulator Kit and Software (Practice flying airplanes and helicopters on your computer) Training Video CD (RC Helicopter & Airplane Education) English Manual